Mombu the Chevrolet Forum sponsored links

Go Back   Mombu the Chevrolet Forum > Chevrolet > GM Diesel (6.2L) fuel filter replacement
User Name
Password
REGISTER NOW! Mark Forums Read

sponsored links


Reply
 
1 23rd June 03:16
bw
External User
 
Posts: 1
Default GM Diesel (6.2L) fuel filter replacement


Followed directions in the manual.
New filter is latched on, with the drain shut and the vent open.
Pulled pink wire from the injector pump solenoid.
How long does it take to crank the engine to fill the new filter??
Cranked about 6 times for 10 seconds with intervals of several minutes to
keep from overheating the starter. I still don't see any fuel coming out the
vent.
  Reply With Quote


  sponsored links


2 23rd June 03:18
diesel65
External User
 
Posts: 1
Default GM Diesel (6.2L) fuel filter replacement


Yes, It takes awhile to pump the fuel up back thru the filter, that is
if the fuel pump is good.
You could try spraying WD-40 down the intake manifold while cranking to
help the engine spin over faster, do not use ether. Also cycle the glow
plugs before cranking.

Bill
  Reply With Quote
3 23rd June 03:18
franko
External User
 
Posts: 1
Default GM Diesel (6.2L) fuel filter replacement


Hard on the starter/battery but you have to do it that way or risk getting
your GM diesel's fuel injection pump airlocked (even harder on your
starter/battery and requires loosening of a couple of injector lines).

If you install an (aftermarket) electric lift pump (e.g., Autozone part
#E-8012-S for about $45), post filter changes become extremely easy on labor
and on the starter/battery.

You can wire it so that the electric lift pump gets juice:
a). from the main fuse block ignition circuit
b). from the main fuse block ignition circuit through an oil pressure switch
(for safety reasons in an accident)
c). directly from the POS battery terminal (use a heavy duty 12V toggle
switch to power it for air bleeding your new diesel fuel filter)

I have mine wired using a three-position toggle switch (On1-Off-On2) where
On1 is wired to a. above and On2 is wire to c. above (someday, I'll install
and wire it through an oil pressure switch e.g., Napa 701-1575)

May I suggest that you install a Racor 645 diesel fuel filter/water
separator between the fuel tank and the electric lift pump (cheapest I've
bought from is OilGuard.com/online/...Other Racor Products for $80 for the
30micron filter).

All the above information, plus more, is available on 62-65dieselpage.com.
Good luck.

Franko
  Reply With Quote
4 23rd June 03:19
bw
External User
 
Posts: 1
Default GM Diesel (6.2L) fuel filter replacement


Thanks for the ideas. The electric pump is the smart way to go. I've been
asking around and found out a neighbor has done almost exactly the same
thing to his 84 GM 6.2L, worked good.
Will probably go over the entire fuel system anyway since my 85 has been
sitting for 3 years with only a few gallons of fuel being taken from the
tank.
  Reply With Quote
5 23rd June 03:19
franko
External User
 
Posts: 1
Default GM Diesel (6.2L) fuel filter replacement


Hello bw,

Unless you are able to drop the fuel tank to clean it, you'll most probably
clog up the 1st in-line fuel filter once you start pumping the diesel out of
the tank. In that case, install the electric lift pump which comes with a
small metal fuel filter attached, prime/air-bleed your fuel system, discard
the metal filter, install the Racor and hopefully, there is not much gunk in
the fuel tank. The Racor filter elements run about $22-$25 each and are
available in 30, 10, 1micron models (1 or 2 microns, I forget).

Before you do any of the above, you could try and drain the fuel tank (if
you cannot drop it) by siphoning out the diesel safely as follows:

1. You'll need two lengths of clear plastic tubing (1/2" or 3/4"), one about
1'-2' long, the other long enough for one end to reach the bottom of the
tank and the other end touching the ground.
2. With the long hose in place, stick the other end into a diesel-safe
container on ground level (lower than the fuel tank).
3. Stick the shorter hose into the fuel filler.
4. Tightly cover both hoses and the filler with a clean cloth (air tight).
5. Blow into the short hose until diesel starts flowing out the long hose.
That should start the siphoning action.

Good luck and let us know how you go.

Franko
  Reply With Quote
Reply


Thread Tools
Display Modes




Copyright 2006 SmartyDevil.com - Dies Mies Jeschet Boenedoesef Douvema Enitemaus -
666