Mombu the Ford Forum sponsored links

Go Back   Mombu the Ford Forum > Ford > 3.8 lean O2s blues..
User Name
Password
REGISTER NOW! Mark Forums Read

sponsored links


Reply
 
1 1st January 09:32
dark1
External User
 
Posts: 1
Default 3.8 lean O2s blues..


I've a 90 Tbird with a 3.8, which began running like it was missing a couple
plug wires only when cold, and giving me a check engine light after ~20min
of driving..
Any time I turn the car off the light stays out for about the same period
after restarting, even if it starts back up immediately..
So I borrow a code scanner, and retrieve codes for the O2 sensors being lean
on both sides (41 & 91)..
So I buy both O2 sensors, new plugs,wires,dist cap, rotor button, and coil.
I installed everything except 1 O2 sensor which I couldn't remove for the
life of me.. just couldn't break it loose in that small of a space (was hard
pressed to even get the ratchet to click). So I stuck with the parts that
were in, reset the ECM by disconnecting power 60secs, fired it back up, and
tested again..
SAME CODES =(
Well that pretty much tells me it wasn't the sensors.. return the other one
and put the 40 bucks into something else..
But the car runs like a champ now, no more miss, but I still get the check
engine light and same codes..
So I replace all the vacuum lines that don't disappear into the firewall on
me.. no change..
egr was mounted a little loose(had to do head gaskets last november),
tightened it up.. nada.. no change..
I waited until the light came on and tested without turning the car off..
same codes.. but the check engine light did go out after the test..
So what could be causing the lean O2 codes without really hurting
performance much?
  Reply With Quote


  sponsored links


2 1st January 10:14
External User
 
Posts: 1
Default 3.8 lean O2s blues..


Possibly a dirty injector or two - it only needs ONE cyl to be lean to
throw a code. My 2.5 Mysique was doing the same until I ran a motorvac
session on it -(cleans all injectors and FPR)
  Reply With Quote
3 1st January 10:14
dark1
External User
 
Posts: 1
Default 3.8 lean O2s blues..


But it's throwing a code for each side.. so I would think it would be
something common to them..
  Reply With Quote
4 1st January 10:15
aarcuda69062
External User
 
Posts: 1
Default 3.8 lean O2s blues..


Does it have an air pump?
  Reply With Quote
5 1st January 10:15
dark1
External User
 
Posts: 1
Default 3.8 lean O2s blues..


no
  Reply With Quote
6 1st January 10:15
aarcuda69062
External User
 
Posts: 1
Default 3.8 lean O2s blues..


Okay...

Of all the parts you've mentioned, there isn't a fuel filter
listed. A restricted fuel filter would cause a lean condition
common to both banks of the engine.

What is the fuel pressure and delivery volume?

Have you checked for vacuum leaks?
  Reply With Quote
7 1st January 10:15
dark1
External User
 
Posts: 1
Default 3.8 lean O2s blues..


good question, and if I was still equipped to answer them, I would.. I
figured a fuel pressure problem would result in it falling on it's face when
it was hammered down, or atleast some loss of power @ high RPM, the opposite
being true, the higher rev, the better acceleration is.. either way a fuel
filter isn't costly enough to skip over, I'll be sure to pick one up
tommorow.
As for the vacuum, I've had my head around the EGR for a while swearing I
hear a hiss, but could never pinpoint it with that mechanical fan clutch the
guys at advance auto parts talked me into making it windy as hell under
there..that's why I replaced all the lines short of the firewall. I don't
own a vacuum guage but if this is really the direction I'm going in I could
get ahold of one and plug those that do go into the firewall for a
test,reconnect them and test again to narrow it down those just run the
heater controls and shouldn't affect anything if disconnected and plugged
right?
  Reply With Quote
8 1st January 10:16
backyard mechanic
External User
 
Posts: 1
Default 3.8 lean O2s blues..


Did you clean the MAF?

It COULD be the Filter, but the one common thing that would act as you
described would be a dirty MAF, though you dont describe 'pinging' or
spark knock on acceleration.

Go to tccoa.com for general directions - EXCEPT:

It's NOt as fragile as described,
1. a medium bristled brush - like a cheap paintbrush- will help lots,
just dont 'bump' the element

2. do NOT use windex, unless you clean its residue with alcohol.
- but why not just use rubbing alcohol in the first place
  Reply With Quote
9 1st January 10:16
dark1
External User
 
Posts: 1
Default 3.8 lean O2s blues..


I wish mine was quite as well placed as that site has it.. lol..
I'll give it a shot though.. thanks..
  Reply With Quote
Reply


Thread Tools
Display Modes




Copyright 2006 SmartyDevil.com - Dies Mies Jeschet Boenedoesef Douvema Enitemaus -
666